3D-ADD GrapEK1-SWCNT Bio, biocompatible electrically conductive single wall carbon nanotubes 3D additive

3D-ADD GrapEK1-SWCNT Bio is an ultra effective electrically and thermally conductive single wall nanotubes additive for 3D printing conductive materials.

It is supplied in powder form as a predispersed conductive additive and is designed for use in compatible 3D resins for conductive applications.

Designed for use with compatible 3D resin systems to prepare electrically and thermally conductive materials for 3D printing. Improved conductivity can be achieved when used with 3Dresyn NSEK Bio.

• 3D printing conductive materials

• Typical achievable values at 0.5 % dosage by weight at 250 microns*: Sheet resistance <40 000 – 4 000 000 kΩ/square
• Typical achievable values at 0.5 % dosage by weight at 250 microns*: Conductivity >0.001 – 0.1 mS/m
• Typical achievable values at 1 % dosage by weight at 250 microns*: Conductivity >1-10 mS/m
• Typical achievable values at 1 % dosage by weight at 250 microns*: Sheet resistance <400 – 4 000 kΩ/square
• Typical achievable values at 1 % dosage by weight at 250 microns*: Resistivity <1×10⁴ – 1×10⁵ Ω.cm
• Z layer thickness of >20-40 microns (>0.02-0.04 mm) can be printed even with low power printers*
• Guaranteed shelf life of 12 months
• Delivery time is around 2-3 weeks after ordering

• Predispersed conductive single wall nanotubes additive in powder form
• Excellent compatibility with most 3D resins
• Improved conductivity can be achieved when used with 3Dresyn NSEK Bio

• Easy and optimum dispersion in 3D resins with Cowles or vortex mixers at 1500 rpm for 5 minutes
• Dosage of 3D ADD GrapEK1-SWCNT Bio can be custom adjusted
• Typical dosages of 0.5-1 % (up to 2%) are recommended
• Excessive dosage may promote the formation of clusters, or clumps (sea-island or nodular structures) and asymptotic behavior of the percolation network
• The higher the dosage the lower the cured thickness and the printable Z layer thickness
• More more information read: Instructions for Use IFU for conductive resin systems
• Please do not expose 3Dresyns to direct natural or artificial room light to prevent curing

• Biocompatible
• Electrically conductive
• Thermally conductive

Conductivity of 3D printed parts will depend on several variables, such as % 3D-ADD GrapEK1-SWCNT Bio, the contribution to promote conductivity of the chosen 3D resin, the degree of dispersion of the conductive additive, etc. When 3D-ADD GrapEK1-SWCNT Bio is added online as functional additive to any 3D resin, conductivity of the resulting product cannot be guaranteed since conductivity depends on both, 3D-ADD GrapEK1-SWCNT Bio, as well as on the contribution to promote conductivity of the chosen 3D resin. On the other hand, low power 3D printers may exhibit printability limitations at high dosage of 3D-ADD GrapEK1-SWCNT Bio and high Z layers. In such cases reduce Z layer thickness and exposure times accordingly following our Instructions for Use IFU.

This material is supplied as a professional manufacturing material and is not marketed as a finished medical device. Final part performance and suitability must be validated by the user according to the intended application.

This technical datasheet should be used together with the relevant processing, calibration, safety and workflow documentation available in the 3Dresyns® Resources section.

Access the 3Dresyns® Technical Resources (IFU, calibration, CRT, post-processing and troubleshooting)